The water level regulator NIVOMATIC can be installed in several different ways. It is designed for pools that are already built or that are in the process of construction or renovation. It is a peace of equipment for comfort and security, which is necessary for different hydraulic systems : pump, automatic covers, etc ...
Your pack is delivered with three supports, that enable several possibilities of installation. For example, the NivOmatic regulator fits comfortably under the margelles, in certain skimmers, in a water outlet, in a regulation box, in certain types of filtration blocks or even for infinity pools.
NivOmatic can be coupled with an overflow system, this ensures the water level high or low : ideal for automatix covers.
Advantages : Complete Kit, many types of installation : the NivOmatic regulator always finds its place ! / The OFF mode allows for an easy diagnose of possible leaks in your pool : no more over-the-top water bills / Patented system, NF standard valve : a great reliability.
PERMANENT INSTALLATION UNDER THE MARGELLE OR THE DECKING OF AN AUTOMATIC COVER
|
Particularly for new or renovated pools, or above ground pools. Attach the support triangle to the edge of the pool, place the sheath in-between the joints of two margelles to guide the feeding pipe. This system allows for total maintenance of the components.
Above ground pools : unscrew a wooden margelle, attach the support triangle by bending it to the form of the pool wall, then lightly carve the wooden margelle to allow for the passage of the feeding pipe : you connect the pipe, and it's ready ! Average time : 1 hour.
|
OFF mode / Maintenance
INSTALLATION IN A WATER OUTLET, with or without an overflow system
Especially for an installation under the decking of an automatic cover : It is essential to regulate precisely the water level (up and down) to protect your cover. Easy to install compared to traditionnal systems, NivOmatic is invisible in the pool, the maintenance of every component is possible, including the in pipe ! Thus, the system is more reliable. The water outlet is used as an overflow system (heavy down pour, ...). The water level regulation is highly recommanded by all the automatic pool cover manufacturers ...
|
 |
Installation :
|
The axis of the water outlet must be placed between 0 to 45mm higher than the required water level. This water outlet must be connected to a flexible PVC pipe (diam. 50mm, length 1,75m) at the end of which will be placed a casing (an irrigation box, ...). In that box the alimentation will be connected, if possible with a tap to protect against frost. A PVC T pipe can be placed as indicated in the diagram to allow the overflow. N.B. : an optionnal alimentation kit (15m reinforced pipe + connexion set) can be provided. |
| |
|
AUTOMATIC COVERS : The water level regulator NivOmatic allows a very simple and efficient installation. It is invisible in the pool, every part is accessible for maintenance, and the alimentation sheath goes through the existing trench when you build your pool. This process not only securises the installation of the automatic cover, but also provides to the professional an economy of time. The flexible sheath allows for a long-life installation, even after the ground settles into place. |
 |
IN A REGULATION BOX
Renovation of an existing system, pools being built. This installation is similar to a traditional one, with a water outlet under the water level, but the feeding pipe goes through a flexible sheath, allowing the check or replacement of the feeding pipe. Increasing reliability and easier maintenance.
|
 |
IN A SKIMMER
|
For the pools being renovated, in which no alternative solution is possible. The skimmer must be equiped with an overfilling system (32 to 40mm). You just need to pierce the hole, to make the same installation as described above and to use the special stainless steel support included in your kit. The skimmer basket can be emptied using the front or the top opening.
|
IN SOME FILTRATION BLOCKS, INSIDE A BUFFER TANK
For most of the swimming pools equiped with a filtration block, already built or being built. Use the support triangle, which can be cut and adjusted. The installation is invisible, quick, the feeding pipe, inside a sheath, goes in the main trench for the filtration block connexion : simple, discrete and functional.
For some infinity pools, built or being built or renovated, you can also adapt NivOmatic inside a buffer tank. The installation relies on the support triangle, which can be cut and adjusted following the dimensions of the tank. This installation is quick and economic.
|
 |
OFF mode : t surveillance d'éventuels défauts d'étanchéité du bassin
The function of a water level regulator is to compensate automatically the losses of water due to evaporation, wind or swimming.
It is generally considered that the water level of a pool should not diminish more than 5 cm / week, depending of the size of the pool, the weather conditions, the use, etc ...
Other factors, for example a leak in the pool or in the pipes, can however be hidden by a water level regulator : the consequency can be, for traditionnal regulators, a dramatic water consumption.
|
NivOmatic is the only hydraulical water regulator that has an integrated OFF mode. In the case of doubt, or from time to time, all that is needed is to insert the provided token or a coin into the slot on the left of the regulator. This closes the valve until the token is removed. This way, you can measure the amount of water lost daily and see just how watertight your pool is. If in doubt, you can always call your pool expert.
The diagnosis can be done quickly, and loss of water is remedeed !!! |
MAINTENANCE
NivOmatic must be connected to domestic clear and pure water. During the use of NivOmatic, a rince of the regulation box with chlorinated water can be useful. Regulation box in ABS, reinforced PVC pipe, supports in stainless steel (316L) : we use quality materials, for a better durability of our products.
HOME | PERMANENT INSTALLATION | REMOVABLE INSTALLATION | NivOmatic PROFESSIONALS | BUY 
